Miele 13384721USA Bedienerhandbuch PDF herunterladen

fold here fold here fold here fold here fold here

fold herefold herefold herefold herefold here

fold here

Quick Start Guide

Steam Ironing System

FashionMaster

These short instructions are not a substitute for the operating instructions

supplied with the appliance!

It is essential to familiarize yourself with the steam ironing system before using

it for the ﬁrst time. Take note of the operating instructions, as well as the

"IMPORTANT SAFETY INSTRUCTIONS".

en-US,CA M.-No. 10 462 481 / 02

Frequently asked questions

AUTOMATIC RINSING / AUTOMATIC DESCALING

Automatic rinsing / descaling Automatic descaling Automatic descaling Frequently asked questions Frequently asked questions

Automatic rinsing

ĺ Adjust the steam ironing system to its highest working height.

ĺ If the message "Fill water container" is shown in the display, fill the water cont-

ainer (see "Filling the water container").

ĺ If the message "Empty residual water container" is shown in the display, remo-

ve and empty the residual water container.

ĺ Clean and dry the residual water container.

Make sure that the metal disks (contacts) at the top of the residual water con-

tainer are cleaned and dried properly. These metal discs send a signal to the

steam ironing system when the residual water container is full or if it is inserted

into the tower.

The discs will not function correctly if they are dirty or damp.

ĺ Slide the residual water container back into the tower until the container clicks

into place.

Clean the water container and fill it up to the level marking

ĺ Remove the residual water container out of the tower when prompted to do so.

ĺ Rinse the water container thoroughly. Make sure there are no residues of the

descaling tablets remaining in the water container.

ĺ Fill the water container with fresh water at least up to the level marking.

ĺ Put the water container back into the tower.

Descaling

After an activation period of approx. 1hour, the descaling solution is drained

from the steam generator into the residual water container.

The steam generator is then rinsed with water. This rinse cycle takes approx.

5minutes. During this time, the "Rinse (5 min.)" message is displayed.

During the rinsing cycle, the display shows "Rinsing".

As soon as the rinse cycle is completed, the water is drained completely into the

residual water container and the message "Empty residual water container" is

displayed.

Rinsing the soleplate

The iron must not be warm from previous use. Let the iron cool down for at least

60minutes before rinsing the soleplate.

ĺ Make sure that the non-stick soleplate has been removed from the iron.

If the non-stick soleplate is still on the iron, remove it now.

ĺ Refill the water container with fresh tap water.

ĺ Remove the steam hose of the iron or the steamer from

the steam connection on the tower.

ĺ Select "Descale".

ĺ Confirm the selection by pressing the OK button.

ĺ Select "Start descaling".

ĺ Confirm the selection by pressing the OK button.

Filling with descaler

ĺ Fill the water container with fresh water up to the level

marking.

ĺ Add 1 descaling tablet to the water container.

ĺ Press the OKbutton to display the next process step.

ĺ Put the water container back into the tower.

ĺ Follow the instructions in the display.

Finish

Start

Automatic descaling

The steam ironing system must be descaled regularly to ensure that it functions

correctly.

The messages in the display will guide you through the descaling process. The

entire descaling process takes approx. 90minutes.

To optimize the descaling process, start the procedure while the system is still

cold after switching the steam ironing system on.

This way, you avoid a delay of up to 3hours that may be caused by the cool-

down phase.

➨

Emptying the residual water container

ĺ Set the steam ironing system to its highest working posi-

tion in order to remove the residual water container when

prompted to do so.

ĺ Remove the residual water container from the tower.

ĺ Drain the residual water container.

ĺ Clean and dry the residual water container.

Make sure that the metal disks (contacts) at the top of the re-

sidual water container are cleaned and dried properly.

ĺ Slide the residual water container back into the tower until

the container clicks into place.

ĺ Set the temperature selector on the iron to cold so that the

line on the selector is pointing to the indicator light.

ĺ Plug the steam hose of the iron into the steam connection

on the tower.

ĺ If the steam ironing system is switched off, switch it on

now.

As soon as the steam ironing system is ready for use and

steam is available, proceed with the next step.

ĺ Hold the iron over a sink or a heat-resistant container.

ĺ Press the button on the iron for around a minute and tilt the iron. with the tip

of the iron pointing downward slightly.

Hot water and steam will come out of the iron and dislodge any deposits that

have built up. As soon as there is only steam coming out, you can release the

button.

During the rinsing process, hot water and steam come out of the iron.

Danger of injury by burning. Never direct the iron at people, animals or

electrical appliances of any kind.

ĺ Now set the temperature selector on the iron to the highest

temperature settingLinen/Cotton.

The indicator light on the temperature selector will light up

yellow while the iron is heating up. As soon as the indicator

light goes out, the rinsing process is complete.

ĺ Move the iron over a soft, absorbent cotton cloth while it is

still hot. Press the steam button briefly 2-3 times in the

process.

The descaling process is now complete. The steam ironing

system can now be switched off or used.

Problem Possible cause and solution

The steam ironing

system cannot be

switched on.

The appliance does not have any power.

ĺ Check whether

- the plug is plugged in.

- the fuse in your fuse panel is OK.

The height of the

ironing board can-

not be adjusted.

The ironing board is not locked into place on both sides of the

tower.

ĺ Use both hands to pull the ironing board upwards into a ho-

rizontal position until this audibly clicks into place on both si-

des of the tower.

The iron does not

heat up.

The appliance is switched o.

ĺ Use the  button on the control panel to switch the steam iro-

ning system on.

The steam hose is not plugged in properly.

ĺ Plug the steam hose into the steam connection on the tower

again.

The iron has not been used for some time.

ĺ Move the iron or activate the steam button .

The steam button is locked.

ĺ Unlock the steam button by pushing the slider on the iron

forward.

The temperature set on the temperature controller has

already been reached.

ĺ Set the temperature controller to a higher temperature if

necessary.

The appliance is rinsing.

ĺ Wait until the rinsing process has been completed (see "Au-

tomatic rinsing").

The display is indicating a malfunction.

ĺ Please remedy the indicated fault as described in the opera-

ting instructions.

The steam ironing system is damaged.

ĺ Contact Miele Service.

With the help of the following guide, minor faults in the performance of the appliance,

some of which may result from incorrect operation, can be remedied without contacting

the Service Department. For further details, see the operating instructions.

Problem Possible cause and solution

When using the

steam button  on

the iron, drops of

water or deposits

escape from the

steam nozzles.

The temperature selected is too low.

ĺ Set the temperature selector on the iron to at least tempera-

ture setting Silk/Wool.

The iron has not yet

reached the selected temperature.

ĺ Wait until the iron has reached the selected ironing

temperature.

During a longer ironing break, condensation

has accumulated in the steam hose.

ĺ After a break in ironing, do not direct the first burst of steam

onto the garment.

Deposits have formed in the soleplate.

ĺ Rinse the soleplate as described in "Automatic descaling".

The fan on the

ironing board is not

running.

Steam was not used.

ĺ The fan only runs when the steam function on the iron is

activated

The steam is not ready yet.

ĺ Wait until the message "Ready" appears in

the display to indicate that steam is ready.

The water container is empty or missing.

ĺ Refill the water container with fresh tap water and replace it

in the tower.

The steamer is connected to the steam ironing system.

ĺ The fan only runs when the iron is connected. Connect the

iron if required.

There is a fault with the steam ironing system.

ĺ Contact Miele Service.

Display

message

Possible cause and solution

 Drain valve fault

Switch on/off

The descaling or rinsing processes have not been

carried out properly.

ĺ Press the  button to switch the steam ironing system off

and then back on again.

ĺ If the fault message continues to be displayed, contact Mie-

le Service.

 Release steam

button

The iron has switched itself o because it has not been used for

a period of time

and the steam button has locked.

ĺ Unlock the steam button by pushing the slider for conti-

nual steam on the iron forward.

 Drain valve fault

Switch on/off

The residual water container has not been detected.

ĺ Press the  button to switch the steam ironing system off

and then back on again.

After switching the steam ironing system o and back on, the

residual water container has not been detected.

ĺ Press the  button to switch the appliance off.

ĺ Clean and dry the metal disks (contacts) on the residual wa-

ter container.

ĺ Use the  button to switch the steam ironing system back

on and follow the instructions shown in the display:

ĺ Remove the residual water container and fill it with fresh tap

water.

ĺ Put the filled residual water container back in the tower.

ĺ Remove the residual water container again when you are

prompted to do so by the appropriate message in the

display.

ĺ Empty and dry the residual water container.

ĺ Put the empty residual water container back in the tower.

The steam ironing system is ready for use again and continu-

es with the process that had been started when the fault was

detected.

There is a fault with the steam ironing system.

ĺ If the fault message continues to be displayed, contact Mie-

le Service.

Frequently asked questions

1 2

Inhaltsverzeichnis

Seite 1 - FashionMaster

fold here fold here fold here fold here fold herefold herefold herefold herefold herefold herefold herefold hereQuick Start GuideSteam Ironing SystemF

Seite 2 - Assembly

fold herefold here fold here fold here fold here fold herefold herefold herefold herefold herefold herefold hereThis is how the steam ironing system i

Kommentare zu diesen Handbüchern

Keine Kommentare

Miele 13384721USA Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Eisen Miele 13384721USA herunter. Miele 13384721USA User manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Eisen Miele 13384721USA