Miele KM 344 Bedienungsanleitung

Installation InstructionsGas CooktopsKM 342KM 344To prevent accidents andmachine damage,read these instructionsbefore installation or use.UV05 649 320

This appliance must be electricallygrounded according to local or na-tional codes.All electrical work should be per-formed by a qualified electrician

Wiring diagramElectrical connection11

Installation and service must be per-formed by a qualified installer, ser-vice agency or the gas supplier.In Massachusetts a licensedplumber/gasfitter

Make sure that the maximum gas sup-ply pressure before the gas pressurereguator is never more than1/2psi forboth natural gas or LP gas.The minimum req

Gas pressure regulatorA pressure regulator that is convertiblefrom natural to LP gas (Propane) is in-cluded with the appliance. The ad-justed pressure

Nominal Rating TableKM 342 G KM 344 GNG / LP-Gas NG / LP-GasNormal burner BTU/hr kW BTU/hr kWMax. output 9.000 2.6 9.000 2.6Min. output 1.700 0.50 1.7

All cooktops come set for connection toeither natural gas or LP gas. The ad-justment of the included regulator cor-responds with the gas type of theco

To convert the burnersTurn off the main gas supply (if theappliance has already been in-stalled) and disconnect the appli-ance from the main electrial

To change the orifices and needlevalves the appliance has to be openedby removing the burners.Normal/Fast burner^ Remove the grates and the burnercap,

Changing the needle valvesNormal/Fast burner^ Take off the ignition switch, a.^ Loosen the needle valve, b, with ascrewdriver and remove them with apa

2WARNING:If the information in this manual is not followedexactly, a fire or explosion may result causingproperty damage, personal injury or death.–Do

Changing the orificesNormal/Fast burnerWok burner^Using a 7mm nut driver or socketwrench, unscrew the orifice.^Install the new orifice according tothe

Changing the small burner orificed Small burner orificee Air sleevef Air vent^First, loosen fitting, c, using an 8 mmwrench. Hold nut, b, with a 12 mm

Check the intake aira Lock screwb Air sleeveGap X must measure:–1/2" (13 mm) for natural gas–1/4" (6.5 mm) for LP gas^To adjust the gap, loo

After conversion–After converting the cooktop unit toLP gas, stick the label supplied withthe conversion kit next to the dataplate underneath the appl

M.-Nr. 05 649 320 / VAlteration rights reserved / 2702This paper consists of cellulose bleached without the use of chlorine.02

Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Appliance dimensions. . . . . . . . . .

InstallationThe minimum distances given inthese Installation Instructions mustbe observed in order to ensure safeoperation. Failure to do so increases

Gas appliances should only be in-stalled in a well ventilated area.Install the appliance so that thepower cord or gas piping does notcome into contact

KM 342a Built-in depthAppliance dimensions6(max.R4 mm)(914mm)36"(889mm)35"(542mm)(518mm)2033(min.635mm)25"(min.47mm)1(min.70mm)23 / 4

KM344a Built-in depthAppliance dimensions7(1079mm)421 / 2 "(1054mm)411 / 2 "(542mm)215 / 1 6 "(518mm)203 / 8 "(min.70mm)2

Setting the cooktop into place^Remove the protective backing, d,from the seal, c, supplied and stick itunder the edge of the cooktop.^Screw the gas re

The cooktop must not be perma-nently sealed into the countertopwhen installed.If the cooktop is sealed into position,the countertop or appliance could