Miele 27102850USA Handbuch

Operating and InstallationInstructionsGas CombisetCS 1028To prevent accidents andappliance damage,read these instructionsbeforeinstallation or use.M.-

Burnerd Burner cape Burner headf Cover plateg Ignitorh Ignition safety control(Thermocouple)i Burner baseGuide to the combiset10

Cleaning the combisetBefore using for the first time clean theappliance as follows:^Remove any protective foil.^Wash the removable parts of the gasbur

Turning on and off / RegulatingThe control knob is used to turn on theburner and to regulate the strength ofthe flame.ß The gas supply is turned off*

Adjusting the flameThe burner can be variably adjustedbetween the lowest and highest flameby turning the control knob.Since the outer portion of the f

Pan size–Set the combiset to a high flamewhen using a large diameter pan andlow flame when using a smalldiameter pan.–Generally, wide / shallow pans w

Ignition Safety ControlThis gas combiset incorporates anIgnition Safety Control which stops thesupply of gas if the flame goes out.^To reignite the bu

Never use a steam cleaner to cleanthis combiset. Pressurized steamcould cause permanent damage tothe surface and to components forwhich the manufactur

BurnerDo not clean any parts of the burnerin a dishwasher.The burner can be dismantled andcleaned when cool.^Remove the burner parts and washthem in a

,Repairs should only be carries out by an authorized technician inaccordance with local and national safety regulations. Unauthorized repairscould cau

In the event of a fault which you cannoteasily fix yourself, please contact theMiele Technical Service Department atthe address on the back of this bo

2WARNING:If the information in this manual is not followedexactly, a fire or explosion may result causingproperty damage, personal injury or death.–Do

MieleCare(USA only)MieleCare, our Extended ServiceContract program; gives you theassurance of knowing that yourappliance investment is covered by 5yea

Installation InstructionsIMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USETo prevent accidentsand appliance damageread these instructionsb

InstallationThe minimum distances given inthese Installation instructions are tocombustible surfaces, and must beobserved to ensure safe operation.Fai

Safety distances above theapplianceThe minimum safety distance given bythe hood manufacturer must bemaintained between the combiset andthe hood above

Safety distances to the sidesof the applianceThe appliance should only be installedas shown in the illustrations, whilemaintaining the required safety

Safety distance from the wall coveringIf a wall covering is installed, a minimum safety distance must be maintainedbetween the countertop cut-out and

Installation dimensionsa Spring clipsb Appliance frontc Installation heightd Power supply box with connection cable,L=783/4" (2000 mm)e Gas fitti

Cut out^Make the countertop cut-out for oneor more appliances as applicable.Remember to maintain a minimumsafety distance from the back wall,as well a

Installation of multipleappliancesWhen installing more than one combiset appliance, a support bar b must beinstalled between the appliances.Countertop

Sample calculations for a countertop cut-out for three appliancesAappliance widthminus 5/16"(8 mm)Bappliance widthCappliance widthminus 5/16"

IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Guide to the combiset . . . . . . . . . . . . . . . .

a Spring clipsb Support barsc Space between support bar and countertopd Sealing stripThe illustration represents the attachment of spring clips a and

Attach the spring clips andsupport barsWood or solid surface countertops^Place the supplied spring clips aand the support bars b at themarked position

Granite countertopThe screws are not needed forgranite countertops.^Position and attach the spring clipsa and support bars b with strong,double-sided

Installing the appliance /appliances^Feed the power cord down throughthe cut-out.^Place the front edge of the applianceinto the cut-out.^With a hand o

SealingThe appliance must not be permanentlysealed into the countertop wheninstalled. The sealing strip under theedge of the appliance provides asuffi

This appliance must be groundedaccording to local or national codes.All electrical work should beperformed by a qualified electricianin accordance wit

Wiring DiagramElectrical connection36

Installation and service must beperformed by a qualified installer,service agency or the gas supplier.In Massachusetts a licensedplumber/gas fitter is

Gas pressure regulatorA pressure regulator that is convertiblefrom natural to LP gas (Propane) or viceversa is included with the appliance.The include

Nominal ratingsMaximum outputGas type BTU/hr kWNatural Gas (NG) 27,600 8.1Liquid Gas(Propane) (LP)22,200 6.5Minimum outputGas type BTU/hr kWNatural Ga

WARNING- When using your gasappliance follow basicprecautions, including thefollowing:This gas combiset conforms to alluniform safety codes andregulat

The combiset should have beenordered for connection to either naturalgas or LP gas (propane).If the combiset is not configured for theproper type of g

Disposal of packing materialsThe cardboard box and packingmaterials are biodegradable andrecyclable. Please recycle.Ensure that any plastic wrappings,

42

43

Alteration rights reserved / 2409For the most updated manual see the Miele web site.M.-Nr. 07 369 720 / 02

Technical safety~Installation, repair and maintenancework should be performed by a Mieleauthorized service technician. Work byunqualified persons coul

~Before servicing, turn off the gasvalve and disconnect the power supplyby either removing the fuse, unpluggingthe unit or manually “tripping” thecirc

~Do not use pans that extend pastthe burner grate. Using larger pansmay cause the flames to spread outand damage the surroundingcountertop or other co

~Make certain that the power cords ofsmall appliances do not come incontact with the appliance. Theinsulation of the cable could becomedamaged. Danger

a Burner grateb Burnerc Control knobGuide to the combiset9