Miele KM 361 G Bedienungsanleitung Seite 1

Installation instructionsGas-hobsKM 360 / KM 360-1KM 361KM 362 / KM 362-1KM 363To avoid the risk of accidentor damage to the applianceit is essential

KM 361 / KM 363Appliance dimensions and worktop cut-out10

a Building-in heightb Connection boxc Gas connection R1/2- ISO 7-1 (DIN2999)^ Make the worktop cut-out following the dimensions shown above.Remember t

Before installing the appliance check that the location provides the requiredclearances from combustible materials and if necessary provide protection

Clearance above and aroundthe appliancea Range hoodb not less than 650 mm from burner toany horizontal surface over full widthof the appliance.c Burne

Building in^Place the hob in the preparedcut-out.^Feed the electrical connection cablethrough the cut-out and connect.^Make the gas connection (seerel

Under no circumstances shouldsealant find its way between theframe of the top part of the hob andthe worktop.This could cause difficulties if thehob e

All electrical work should be carriedout by a suitably qualified andcompetent person in strictaccordance with national and localsafety regulations.For

Connection to the gas supply, orconversion from one type of gas toanother should only be undertakenby an approved fitter, who isresponsible for correc

The gas connection must be inaccordance with national and localregulations.The relevant building regulationsmust also be observed.Natural gas / liquid

Nominal rating for all gas types with the burner full onBurner GastypeKM 360 / KM 360-1/KM 361KM 362 / KM 362-1 KM 363MJ/h g/h MJ/h g/h MJ/h g/hAuxili

WO This appliance can be used in countries other than those specified onthe appliance. It is, however, set up for connection to the gas and electricit

Jet tableWhen converting to liquid gas, themain jets and the small jets of allburners must be changed.Screw in the new jets according tothe following

Changing the jetsDisconnect the gas hob from theelectricity supply. Depending on thetype of installation, either withdrawthe mains fuse, switch off at

Wok burner^Take off the burner cover a, burnerring b and burner head c.^Loosen the screws d and take off theplate.^Using an (M7) socket spannerunscrew

Changing the low setting jets(all burners)To change the low setting jets thefastening screws of the burners mustbe loosend and the upper part of theap

After conversion^Assemble all burners in the reverseorder and check for leaks byoperating them without the upperpart of the hob in place (use a matcht

25

26

27

Alteration rights reserved / 1605M.-Nr. 05 827 671 / 01en - AUS

Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Appliance dimensions and worktop cut-out .

Building inFit wall units and the cooker hoodbefore fitting the appliance, to avoiddamaging it.The veneer or laminate coatings ofworktops (or adjacent

As a minimum 20 m3space isrequired where the appliance isinstalled, and a door or window whichcan be opened to the outside air.Using the gas hob can c

KM 360 / KM 362Appliance dimensions and worktop cut-out6

a Building-in heightb Connection boxc Gas connection R1/2- ISO 7-1 (DIN2999)^ Make the worktop cut-out following the dimensions shown above.Remember t

KM 360-1 / KM 362-1Appliance dimensions and worktop cut-out8

a Building-in heightb Connection boxc Gas connection R1/2- ISO 7-1 (DIN2999)^ Make the worktop cut-out following the dimensions shown above.Remember t