Miele GAS COMBISET CS 1011 Bedienungsanleitung

Operating and InstallationInstructionsGas CombisetCS 1011To prevent accidents andappliance damage,read these instructionsbeforeinstallation or use.M.-

Burnerg Small burner caph Large burner capi Burner ringj Burnerk Ignition safety control(Thermocouple)l Ignitorm Burner basePositioning the burner par

Cleaning the combisetBefore using for the first time clean theappliance as follows:^Remove any protective foil.^Wash the removable parts of the gasbur

Fast-Ignition SystemThe gas combisets are equipped with aFast-Ignition-System whichincorporates the following features:–The control knob does not need

Turning on^To turn on the burner, press thecontrol knob down to pass theresistance, then release the pressureand turn it counterclockwise to thelarges

On/Off indicator and Residualheat indicatorWhen the combiset is turned on, theOn/Off indicator lights up. Once apre-set temperature has been reached,t

Min. base diameterPots / Pans - 5 7/8" (15 cm)Max. top diameterPots / Pans - 11" (28 cm)–Follow the dimensions given in thetable. If the bot

–Whenever possible, keep pots andpans covered while cooking. Thishelps keep in the most possible heat.–Cook with a small amount of water.–Using a pres

Ignition safety controlThis appliance is equipped with anIgnition Safety Control. This control cutsthe gas supply if the flame goes outand reignition

Never use a steam cleaner to cleanthis combiset. Pressurized steamcould cause permanent damage tothe surface and to components.Do not use any sharp or

BurnerThe burner can be dismantled andcleaned when cool.^Remove the burner parts and washthem in a solution of hot water andliquid dish soap. Dry them

2WARNING:If the information in this manual is not followedexactly, a fire or explosion may result causingproperty damage, personal injury or death.–Do

,Repairs should only be carries out by an authorized technician inaccordance with local and national safety regulations. Unauthorized repairscould cau

The burner does not ignite after several attempts.Possible fault SolutionDisconnect the appliance from the electrical supply for a few seconds. If the

The igniter does not spark.Possible fault SolutionThe circuit breaker has tripped. Re-set the circuit breaker. Contact anelectrician for assistance if

In the event of a fault which you cannoteasily fix yourself, please contact theMiele Technical Service Department atthe address on the back of this bo

MieleCare(USA only)MieleCare, our Extended ServiceContract program; gives you theassurance of knowing that yourappliance investment is covered by 5yea

Installation InstructionsIMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USEInformation is subject to change. Please refer to our website to

InstallationThe minimum distances given inthese Installation instructions are tocombustible surfaces, and must beobserved to ensure safe operation.Fai

Safety distances above theapplianceThe minimum safety distance given bythe hood manufacturer must bemaintained between the combiset andthe hood above

Safety distances to the sidesof the applianceThe appliance should only be installedas shown in the illustrations, whilemaintaining the required safety

Safety distance from the wall coveringIf a wall covering is installed, a minimum safety distance must be maintainedbetween the countertop cut-out and

IMPORTANT SAFETY INSTRUCTIONS...4Guide to the combiset ...9Burner ...

Installation dimensionsa Spring clipsb Appliance frontc Installation heightd Power supply box with connection cable,L=783/4" (2000 mm)e Gas fitti

Cut out^Make the countertop cut-out for thedesired number of appliances.Remember to maintain a minimumsafety distance from the back wall,as well as fr

Installation of multipleappliancesWhen installing more than one combiset appliance, a support bar b must beinstalled between the appliances.Countertop

Sample calculations for a countertop cut-out for three appliancesAappliance widthminus 5/16"(8 mm)Bappliance widthCappliance widthminus 5/16"

a Spring clipsb Support barsc Space between support bar and countertopd CoverThe illustration represents the attachment of spring clips a and support

Attach the spring clips andsupport barsWood or solid surface countertops^Place the supplied spring clips aand the support bars b at themarked position

Granite countertopThe screws are not needed forgranite countertops.^Position and attach the spring clipsa and support bars b with strong,double-sided

Installing the appliance /appliances^Feed the power cord down throughthe cut-out.^Place the front edge of the applianceinto the cut-out.^With a hand o

SealingThe appliance must not bepermanently sealed into the countertopwhen installed. The sealing strip underthe edge of the appliance provides asuffi

This appliance must be groundedaccording to local or national codes.All electrical work should beperformed by a qualified electricianin accordance wit

WARNING- When using your gasappliance follow basicprecautions, including thefollowing:This gas combiset conforms to alluniform safety codes andregulat

Electrical connection40

Installation and service must beperformed by a qualified installer,service agency or the gas supplier.In Massachusetts a licensedplumber/gas fitter is

Gas pressure regulatorA pressure regulator that is convertiblefrom natural to LP gas (Propane) or viceversa is included with the appliance.The include

Nominal ratingsMaximum outputGas type BTU/hr kWNatural Gas (NG) 17,500 5.2Propane (LP) 17,500 5.2Minimum outputGas type BTU/hr kWNatural Gas (NG) 680

The combiset should have beenordered for connection to either naturalgas or LP gas (propane).If the combiset is not configured for theproper type of g

Disposal of packing materialsThe cardboard box and packingmaterials are biodegradable andrecyclable. Please recycle.Ensure that any plastic wrappings,

46

47

Alteration rights reserved / 3911INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOSTCURRENT PRODUCT SPECIFICATIONS, TECHN

Technical safety~Installation, repair and maintenancework should be performed by a Mieleauthorized service technician. Work byunqualified persons coul

~Before servicing, turn off the gasvalve and disconnect the power supplyby either removing the fuse, unpluggingthe unit or manually"tripping"

~Do not use pans that extend pastthe burner grate. Using larger pansmay cause the flames to spread outand damage the surroundingcountertop or other co

~If there is a drawer directlyunderneath the appliance without awooden base in between, ensure thatno aerosols, combustible liquids orother easily fla

a Wok burnerb Burner gratec Control knobd DisplayIndicatorse On/Off indicatorf "Residual Heat" indicatorGuide to the combiset9