Miele GAS KM 81-2 Betriebsanleitung PDF herunterladen (Seite 14)

(CDN) (USA) Instructions for building-in

Prepare the cooktop cut-out as illus-

trated.

Dimension "B" applies for a combina-

tion of appliances and is given on

the chart.

Dimension "X":

CDN:

The typical depth of a counter-

top is 635 mm. "X" must be a mini-

mum of 90 mm.

USA: "X" must be a minimum of 2 1/4".

2 zone Combiset

1 Combiset

2 Combisets

3 Combisets

4 Combisets

5 Combisets

4 zone Combiset

1 Combiset

2 Combisets

3 Combisets

Combination

One 2 zone

+ one 4 zone

Two 2 zone

+ one 4 zone

Three 2 zone

+ one 4 zone

One 2 zone

+ two 4 zone

Two 2 zone

+ two 4 zone

Depth

in

mm

490

490

490

490

490

490

490

490

490

490

490

490

490

Width *

(= Dimen-

sion B)

in mm

265

558

851

1144

1437

560

1143

1728

851

1143

1437

1436

1729

Extractor (e.g. DA 8-2)

For building in between two appliances:

- Dimension B increases by 90 mm.

For building in at the end of a combination:

- Dimension B increases by 98 mm.

* Width includes provision lor V 98 spacer bar.

2G

(CDN) (USA) Instructions for building-in

2 zone Combiset

1 Combiset

2 Combisets

3 Combisets

4 Combisets

5 Combisets

19-5/16"

19-5/16"

19-5/16"

19-5/16"

19-5/16-

Depth

in

inch

Width *

(= Dimen-

sion B)

in inch

10-7/16"

22"

33-1/2"

45-1/32"

56-9/16-

4 zone Combiset

1 Combiset

2 Combisets

3 Combisets

Combination

One 2 zone

+ one 4 zone

Two 2 zone

+ one 4 zone

Three 2 zone

+ one 4 zone

One 2 zone

+ two 4 zone

Two 2 zone

+ two 4 zone

19-5/16"

19-5/16"

19-5/16"

19-5/16"

19-5/16"

19-5/16"

19-5/16"

19-5/16"

22'

45"

68"

33-1/2"

45"

56-9/16"

56-1/2"

68-1/16"

Extractor (e.g. DA 8-2)

For building in between two appliances:

- Dimension B increases by 3 9/16".

For building in at the end of a combination:

- Dimension B increases by 3 7/8".

* Width includes provision for V 98 spacer bar.

Place the seal provided © under the

edge of the cooktop.

© Appliance

® Tensioning screw

© Clamp

© Countertop

©Seal

• Turn the tensioning screws © in a -

clockwise direction © until a resist-

ance is felt, then turn the clamp to

the left.

• Place the appliance in position, turn

the clamps and tighten the tension-

ing screws until the clamps just

touch the countertop ©. Do not over-

tighten.

• Connect the appliance to the electri-

cal supply.

When building-in several Combiset

units,

a stainless steel spacer bar (V 98

edge connector) must be installed be-

tween each unit. It is supplied with its

own installation instructions.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 20 21

Kommentare zu diesen Handbüchern

Keine Kommentare